A practical sizing guide from the factory that builds 3000W inverters — voltage, amp-hours, runtime and chemistry, with real numbers you can copy.
Short answer: a 3000W inverter runs best on a 48V battery bank of at least 100Ah lithium (LiFePO4) or 200–300Ah lead-acid. That is the honest minimum for full load. How much more you need depends only on how long you want to keep drawing power — the formula below tells you exactly.
Buyers ask us this question every week, because the battery is where most DIY solar and backup systems go wrong: too small a bank sags the inverter into low-voltage shutdown, while the wrong voltage turns simple wiring into a heater. Here is how to get it right the first time.
An inverter draws watts ÷ battery voltage ÷ efficiency from the bank. At 3000W output, the current on the DC side looks like this:
| Battery voltage | DC current at full 3000W load | Verdict for a 3000W unit |
|---|---|---|
| 12V | ~280A | Not recommended — needs 2/0 or 4/0 cable, huge fuses, severe voltage sag |
| 24V | ~140A | Workable for compact installs; keep cables under 1 m |
| 48V | ~70A | Best choice — modest current, thin cables, cool connectors, room to grow to 6kW+ |
That is why our TS 3000W pure sine wave inverter series ships in 24V and 48V versions, and why every serious 3kW+ system we build moves to 48V. If you are also charging from solar, the SY hybrid inverter series (3.5–6.2kW) already integrates a 48V-capable MPPT charger and battery inverter in one box.
Use this formula:
Ah = (Load in W × hours) ÷ (battery V × inverter efficiency × depth of discharge)
With typical values — 90% inverter efficiency, 90% usable depth for LiFePO4, 50% for lead-acid — a full 3000W load on a 48V bank works out to:
| 48V battery bank | Usable energy | Runtime at 3000W | Runtime at 1500W |
|---|---|---|---|
| 100Ah LiFePO4 | 4.1 kWh | ~1 h 20 min | ~2 h 45 min |
| 200Ah LiFePO4 | 8.2 kWh | ~2 h 45 min | ~5 h 30 min |
| 300Ah LiFePO4 | 12.3 kWh | ~4 h | ~8 h |
| 400Ah lead-acid (50% DoD) | 9.6 kWh | ~3 h 10 min | ~6 h 20 min |
Notice the real-world mix: a fridge, router, lights, TV and a pump rarely average more than 800–1200W, so most households find a single 48V 200Ah lithium bank comfortably runs their essentials through the night. Add a solar array and the right MPPT solar charge controller (60A at 48V is a good match for 3kW of panels), and the same bank cycles every day for years.
Discharges to 80–90% of nameplate, handles 1C output (a 100Ah battery can push 100A — more than a 48V 3000W inverter asks for), and lasts 3,000–6,000 cycles. Smaller, lighter, cheaper per usable kWh over its life.
Keep discharge to 50% and current to about 0.2C, which means a 48V 3000W load wants 300–400Ah. Fine for budget backup, but heavy, and the bank ages fast in daily cycling.
Start lithium even if smaller: a 48V 100Ah pack plus solar charging outperforms a worn-out 400Ah lead-acid string within two years of daily use. Lead-acid only makes sense where upfront cost is the single deciding factor.
At 48V, full load is roughly 70A: use an 80–100A ANL or class-T fuse within 30cm of the battery positive terminal, 16–25mm² (6–4 AWG) cable for short runs, and keep the battery-to-inverter leads under one metre. Set the inverter's low-voltage cutoff to the battery maker's spec (typically 42–44V for a 48V LiFePO4 pack) so the BMS never has to do the inverter's job. On 12V and 24V systems, every one of those numbers gets dramatically harder — which is exactly why we recommend 48V from day one.
For a 3000 watt inverter: choose 48V, install at least a 100Ah LiFePO4 battery, and scale amp-hours with the runtime formula above. Pair it with the right inverter and an MPPT charger, and the system will run a decade of daily cycles. Send us your load list and target runtime through the form below — our engineers will confirm the exact model, battery bank and pricing within one business day.
Tell us your system voltage, load and quantity — an engineer replies with model, price and lead time within one business day.